Safety Recall 19V-883 – Transmission Wiring Harness – 2019-2020 BMW M5 & 2020 M8

“This site contains affiliate links for which OEMDTC may be compensated”

December 11, 2019 NHTSA CAMPAIGN NUMBER: 19V883000

Transmission Wiring Harness Can Short Circuit

An electrical short circuit can cause the transmission to shift to neutral resulting in a loss of propulsion, increasing the risk of a crash.

 

NHTSA Campaign Number: 19V883

Manufacturer BMW of North America, LLC

Components POWER TRAIN, ELECTRICAL SYSTEM

Potential Number of Units Affected 3,012

 

Summary

BMW of North America, LLC (BMW) is recalling certain 2019-2020 M5 and 2020 M8 Gran Coupe, M8 Coupe, and M8 Convertible vehicles. The transmission wiring harness can become damaged, resulting in an electrical short circuit.

 

Remedy

BMW will notify owners, and dealers will replace any damaged transmission harnesses. All harnesses will be rerouted and secured. These repairs will be performed, free of charge. The recall is expected to begin February 3, 2020. Owners may contact BMW customer service at 1-800-525-7417.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check if your BMW has a Recall

 


SIB 12 30 19
2019-12-13

RECALL 19V-883: TRANSMISSION WIRING HARNESS

Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure the next time the vehicle is in the shop.

This Service Information Bulletin (Revision 2) replaces SI B12 30 19 dated December 2019.

 

What’s New (Specific text highlighted):

  • Recall number updated in the title
  • Interim solution removed from Procedure
  • Parts Information

 

MODEL

E-Series Model Descriptions Production Dates Engine
F90 M5 Sedan January 30, 2019 – October 30, 2019 S63M
F91 M8 Convertible February 20, 2019 – October 30, 2019 S63M
F92 M8 Coupe July 3, 2019 – October 20, 2019 S63M
F93 M8 Gran Coupe June 19, 2019 – October 29, 2019 S63M

 

AFFECTED VEHICLES

Vehicles which require this Recall Campaign to be completed will show it as “Open” when checked either in AIR, the “Service Menu” of DCSnet (Dealer Communication System) or with ISPA NEXT. Recall letter and Q&A are attached.

 

SITUATION

BMW of North America, LLC is conducting a Voluntary Safety Recall (effective December 5, 2019) on certain Model Year 2019-2020 BMW vehicles that were produced between January 30, 2019 and October 30, 2019.

The transmission wiring harness could become damaged due to the location and routing. This could lead to a short circuit, which affects the transmission function; and causes the vehicle to lose propulsion and to shift to Neutral while driving, increasing the risk of a crash.

The Recall Notice and Q&A have been attached for further information.

 

CAUSE

The transmission wiring harness may be damaged due to high temperature, combined with compression from the wiring harness mounting clip. This damage may result in an electrical short circuit in the transmission wiring harness.

 

CORRECTION

Check the vehicle mileage, then repair and/or relocate the transmission electrical harness as described in the required procedure.

 

PROCEDURE

Determine the current mileage displayed in the vehicle’s instrument cluster:

If the vehicle mileage is under six (6) miles and the vehicle has not been delivered (no in-service date) to the customer:

All other vehicles:

Note: The bolts for the transmission crossmember can be reused and do not need to be replaced for this Service Information procedure.

Note for Procedure A and B: The bolts for the transmission cross member can be reused, they do not need to be replaced as part of this bulletin’s repair procedure.

Note: The interim solution is no longer a valid repair procedure because the cable strap with bracket (P/N 34 32 7 708 473) is now available. Vehicles which have been previously repaired with the interim solution do not require additional repairs.

 

PARTS INFORMATION

Note: The bolts for the transmission cross member can be reused, they do not need to be replaced as part of this bulletin’s repair procedure.

Only use and invoice the part numbers below.

Performing a part number look-up in ETK (EPC) by VIN or model in place of using/invoicing the following part numbers may result with the wrong part numbers being invoiced and installed, this could delay the payment of claim.

For Procedure A – Reposition the transmission wiring harness:

Part Number Description Quantity
34 32 7 708 473 Cable strap with bracket 2
61 13 6 902 588 Adhesive tape (orders round to a Qty of 25) 1 (if required)

 

Or:

For Procedure B – Rework the transmission wiring harness

Part Number Description Quantity
34 32 7 708 473 Cable strap with bracket 2
61 13 1 379 833 Shrink hose (orders round to a Qty of 10) 2 (as needed)
61 13 8 353 748 Cable connector (orders round to a Qty of 10) 2 (as needed)
61 13 6 902 588 Adhesive tape (orders round to a Qty of 25) 1 (as needed)

 

WARRANTY INFORMATION

Reimbursement for this Recall will be via normal claim entry utilizing the following information together with the part numbers the above that apply:

Defect Code: 0012150500

 

Completion before the first vehicle delivery to a customer (no in-service date) and the vehicle mileage is under six (6) miles

Work Pkg Labor Operation Description (Plus work) Labor Allowance
# 1 00 68 828 Procedure A – Reposition the transmission wiring harness 6  FRU (F90/F91/F92);

7  FRU (F93)

 

Or:

Completion before the first vehicle delivery to a customer (no in-service date) and the vehicle mileage is six (6) miles and higher but less than 300 miles or it is a delivered vehicle that is already in the workshop

Work Pkg Labor Operation Description (Plus work) Labor Allowance
# 2 00 68 834 Procedure B – Rework the transmission wiring harness 7  FRU (F90/F91/F92)

8  FRU (F93)

 

Or:

The vehicle arrives at your center and this Recall Campaign shows open (No other Main work will be performed/claimed during this workshop visit)

Work Pkg Labor Operation Description (Main work) Labor Allowance
# 3 00 68 248 Procedure B – Rework the transmission wiring harness 9 FRU (F90/F91/F92/F93)
And, with the above as necessary:

Associated work with WP 1, 2 or 3

Labor Operation Description (Plus work) Labor Allowance
00 68 835 Reworking the ground line 1 FRU

 

Claim Repair Comments

Only reference the SIB number and the work package (Pkg) number performed in the RO technician notes and in the claim comments (For example: B12 30 19 WP 1), unless otherwise required by State law. Supporting Materials

picture_as_pdf B123019 Recall Notice.pdf
picture_as_pdf B123019 2019-2020-F9x-TransmissionWiringHarness-QA(11Dec2019).
pdf
picture_as_pdf B123019 Procedure A.pdf
picture_as_pdf B123019 Procedure B.pdf


Attachment to B123019
December 2019

 

SAFETY RECALL NOTICE

 

To:  All Center Operators, Sales Managers, Service Manager, Parts Manager and Warranty Processor

RE: Recall 19V-xxx: Transmission Wiring Harness – B12 30 19

BMW of North America, LLC is conducting a Voluntary Safety Recall (effective December 5, 2019) on a certain Model Year 2019-2020 BMW vehicles that were produced between January 30, 2019 and November 27, 2019. 

Please be reminded that it is a violation of federal law (The Safety Act) for you to sell, lease or deliver any new motor vehicle covered by this notification until the recall repair has been performed.  This means that centers may not legally deliver new motor vehicles to consumers until they are fixed or use/sell replacement equipment/parts subject to this recall.  Note also that substantial civil penalties apply to violations of the Safety Act.  

Also, you should not sell, lease or deliver any Certified Pre-Owned or used vehicles subject to a safety recall until the repair is completed.  

Please follow any special instructions that we provide to you for the return or disposition of recall parts.

  

We appreciate all your assistance with this Recall.


Attachment 1 to SI 12 30 19
December, 2019

RECALL 19V-XXX: TRANSMISSION WIRING HARNESS

PROCEDURE A – Reposition the transmission wiring harness

 

Risk of short circuits! Risk of fire!

Make sure that there is no charger connected to the jump start terminal in the engine compartment.

1. Disconnect all negative battery cables.

2. Remove the transmission cross member by supporting the transmission with special tools 0 495 498 (23 4 050) and 2 219 012. Secure the transmission with lashing straps (1).

3. Release and remove screw (1).

4. Release screws (2).

5. Remove transmission crossmember (3).

6. Disconnect the transfer case and transmission 12 V connectors.

7. Remove the transmission wiring harness (1) from the retaining bracket (2).

8. Remove the transmission wiring harness (1).

9. Remove transmission harness grounding lug.

10. Position the tape measure on the connector housing.

11. Measure the transmission wiring harness with a tape measure. from the transfer case connector housing shown in step 6.

12. Cut two pieces of tape approximately 4 inches long.

Part Number: 61 13 6 902 588

13. Wrap one piece of tape around the harness at approximately 8 5/8 inches.

Wrap the other piece of tape around the harness at approximately 14 ½ inches.

14.  Loosely position the clip with a cable strap (2) on the fabric adhesive tape (1) at approximately 8 5/8″.

15.  Loosely position the clip with a cable strap at approximately 14 ½ inches position.

Part Number: 34 32 7 708 473

16. Secure the clips with the openings facing upwards (see graphic).

The cable strap location must be moved approximately 1 3/16 inches toward the front of the vehicle.

17.  Cut a piece of tape approximately 4 inches long.

18.  Attach the fabric adhesive tape (1) to the transmission wiring harness at approximately 6 ¼ inches from the transmission connector housing.

19. Hook transmission wiring harness (1) to transmission retaining bracket (2) at the transmission tape position.

20. Hook in transmission wiring harness 1 (see graphic).

21. Secure transmission grounding.

Ground connection on the transmission Screw M6 x 12: Tightening torque 10 Nm.

Note: Ensure enough slack so the harness is not pulled taught over the transmission housing casting lines.

22. Install the gearbox cross member (3).

23. Tighten screw (1).

Transmission cross member on rubber mount M12: Tightening torque 68 Nm.

24. Tighten screws (2). Transmission cross member on the body M8:

Tightening torque 19 Nm.

25.  Release the lashing strap (1) from the transmission.

26.  Remove special tools 0 495 498 (23 4 050) and 2 219 012

27. Connect all negative battery cables.

Negative battery terminal Nut: tightening torque 5Nm.

 

RECALL 19V-XXX: TRANSMISSION WIRING HARNESS

PROCEDURE B – Rework the transmission wiring harness

 

Risk of short circuits! Risk of fire!

Make sure that there is no charger connected to the jump start terminal in the engine compartment.

1. Disconnect all negative battery cables.

2. Remove the transmission cross member by supporting the transmission with special tools 0 495 498 (23 4 050) and 2 219 012. Secure the transmission with lashing straps (1).

3. Release and remove screw (1).

4. Release and remove screws (2).

5. Remove transmission crossmember (3).

6. Disconnect the 12 V connectors from the transfer case and transmission.

Branch (1) automatic transmission

Branch (2) transfer box

Branch (3) Not used in US vehicles

7. Push insulating sleeve (1) back in direction of the arrow 100 mm (approximately 4 inches).

8. Open and remove insulating tape (1).

9. Open cable straps (1).

10.  Push insulating sleeve (1) back in direction of the arrow 110 mm (approximately 4 ½ inches).

11.  Check cable for damage.

Important: Steps 12 thru 20 must be performed even if damage is not observed.

12. Position the tape measure on the connector housing.

13.  Measure 470mm (approximately 18 ½ inches) from the transfer case connector housing shown in step 12.

14.  Mark the positive wire in the transmission wiring harness.

15. Cut red positive wire at 470 mm (approximately 18 ½ inches) from the transfer case connector housing.

16. Strip insulation from the ends of the positive wire.

17.  Push the insulating sleeve (1) onto the positive wire.

18.  Crimp the positive wire with butt connector (2).

Part Number 61 13 8 353 748

19.  Insert the insulating sleeve (1) 40 mm (approximately 1 ½ inches) under the heat protection shield.

Part Number 61 13 1 379 833

20.  Heat the heat-shrink tubing (1) with a hot air blower with maximum 150°C (approximately 302°F) until the positive wire is insulated.

21. Check grounding cables (1) for damage and, if necessary, repair with an insulating sleeve.

Note: Do not perform steps 22 thru 27 if damage is not observed.

22.  Strip insulation from ground cable (1) at both ends.

23.  Push insulating sleeve onto ground cable.

24.  Crimp grounding cable with butt connector (2).

Part Number 61 13 8 353 748

25.  Slide the insulating sleeve (1) over the grounding cable.

Part Number 61 13 1 379 833

26.  Slide the insulating sleeve (1) over the grounding cable.

27.  Heat the heat-shrink tubing (1) with a hot air blower with maximum 150°C (approximately

302°F) until the grounding cable is insulated.

28. Push insulating sleeve (1) back into the end position in the direction of the arrow.

29. Secure and cover all insulating sleeves with fabric adhesive tape (1).

Part Number: 61 13 6 902 588

30. Put insulating sleeve (1) over the fabric adhesive tape in the direction of the arrow.

31.  Measure the transmission wiring harness with a tape measure from the transfer case connector housing shown in step 12.

32.  Cut two pieces of tape 100 mm (approximately 4 inches) long.

Part Number: 61 13 6 902 588

33.  Wrap one piece of tap around the harness at 220 mm (approximately 8 5/8 inches).

34.  Wrap the other piece of tape around the harness at 370 mm (approximately 14 ½ inches).

35.  Loosely position the clip with a cable strap

(2) on the fabric adhesive tape (1) at the 220 mm (approximately 8 5/8).

36.  Loosely position the clip with a cable strap 370 mm (approximately 14 ½ inches) position.

Part Number: 34 32 7 708 473

37. Secure the clips with the openings facing upwards (see graphic).

38. Attach the fabric adhesive tape (1) to the transmission wiring harness at 160 mm (approximately 6 ¼ inches) from the transmission connector housing.

39. Hook transmission wiring harness (1) to transmission retaining bracket (2) at the transmission tape position.

40.  Hook in transmission wiring harness (1).

41.  Secure transmission ground lug.

Ground connection on the transmission Screw M6 x 12: Tightening torque 10 Nm.

Note: Ensure enough slack so the harness is not pulled taught over the transmission housing casting lines.

42. Install the gearbox crossmember (3).

43. Tighten screw (1).

Transmission crossmember on rubber mount M12: Tightening torque 68 Nm.

44. Tighten screws (2). Transmission crossmember on the body M8:

Tightening torque 19 Nm.

45.  Release the lashing strap (1) from the transmission.

46.  Remove special tools 0 495 498 (23 4 050) and 2 219 012.

47. Connect all negative battery cables.

Negative battery terminal nut: Tightening torque 5Nm.

 


Transmission Wiring Harness
Safety Recall 19V-xyz
Model Year 2019-2020
BMW M5, M8
Last Updated 12/11/2019

 

Q1. Which BMW Group models in the US are potentially affected by this Safety Recall?

Certain Model Year 2019-2020 BMW M5 and M8 vehicles produced between January and October 2019, are potentially affected.  Please refer to the table below for further details.

E-Series Model Description Production Date
F90 M5 Sedan January 30, 2019 – October 30, 2019
F91 M8 Convertible February 20, 2019 – October 30, 2019
F92 M8 Coupe July 3, 2019 – October 20, 2019
F93 M8 Gran Coupe June 19, 2019 – October 29, 2019

 

Q2. What is the specific issue?

Due to the location and routing of the transmission wiring harness, it could become damaged.  This could lead to a short circuit, affecting transmission function, cause the vehicle to lose propulsion and to shift to Neutral while driving, increasing the risk of a crash.

 

Q3. Why are other BMW Group vehicles not included in this Safety Recall?

Transmission wiring harness location and routing are specific to certain transmissions.

 

Q4. How did BMW Group become aware of this issue?

BMW Group became aware of this issue through its quality control procedures.

 

Q5. Can I determine if this issue exists in my vehicle? 

If you notice that while driving the vehicle loses propulsion and the transmission shifts to Neutral, your vehicle may be experiencing this issue.

 

Q6. What should I do if I notice this condition in my vehicle?

If this condition occurs, please contact your authorized BMW center immediately to have this Safety Recall performed.

 

Q7. Can I continue to drive my vehicle (before I receive my letter)?

Yes.  However, when you receive a letter requesting you to make an appointment to have this Safety Recall performed by an authorized BMW center, please do so as soon as possible.  If you are not the only driver of this vehicle, please advise all other drivers of this important information.

 

Q8. How will my vehicle be repaired?

The transmission wiring harness will be inspected and rerouted or, in some cases, replaced and rerouted, for free and can take approximately one hour.

 

Q9. Is BMW Group aware of any accidents or injuries in the US, involving these BMW Group vehicles associated with this Safety Recall?

No.

 

Q10. How will I be informed of this Safety Recall?

You will receive a letter in February via First Class mail advising you of this Safety Recall and to schedule an appointment with an authorized BMW center to have this Safety Recall performed.  You can locate your nearest authorized BMW center at www.bmwusa.com/dealer.  To ensure the BMW Group has your most recent contact and vehicle information, please register your BMW vehicle at www.bmwusa.com/myBMW.  Registration is free, and will give you access to factory initiated campaigns and other information specific to your vehicle.

 

Q11. Do I have to wait for my letter to have my vehicle serviced?

Yes.  BMW is in the process of ensuring that the necessary tools, parts, and procedures are available prior to contacting you to schedule an appointment with your authorized BMW center to have this important Safety Recall performed.  For the latest updates to this Safety Recall, please visit www.bmwusa.com/recall.

 

 


IMPORTANT SAFETY RECALL Remedy Available

This notice applies to your vehicle,
Recall Campaign No. 19V-883: Transmission Wiring Harness

February 2020

 

Dear BMW Owner / Lessee:

This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. BMW AG has decided that a defect, which relates to motor vehicle safety, exists in certain Model Year 2019-2020 BMW M5 and M8 vehicles. Our records indicate that you are the owner of a potentially affected vehicle.

 

Why are we contacting you?

We are pleased to inform you that we are ready to perform this recall. If you have not had this recall performed, please contact your authorized BMW center immediately to schedule an appointment. Visit www.bmwusa.com/dealer to locate your nearest BMW center.

 

What could happen?

Due to its location/routing, the transmission wiring harness could become damaged. If this occurs, while driving the vehicle may lose propulsion and the transmission could unexpectedly shift to Neutral, increasing the risk of a crash.

If you notice that while driving, the transmission unexpectedly shifts to Neutral or, when depressing the accelerator pedal you hear an increase in engine noise without an increase in vehicle speed, then your vehicle may be experiencing this issue. You may also notice an “N” (instead of a “D”) displayed in the instrument cluster. If this occurs, carefully move away from traffic and pull over to a safe location as soon as possible. All occupants should carefully exit the vehicle and move to a safe location away from traffic. Do not continue to drive the vehicle. Contact BMW Roadside Assistance at 1-800-332-4269 immediately to have your vehicle brought to the nearest authorized BMW center.

If you are not the only driver of this vehicle, please advise all other drivers and passengers of this important information.

 

What will BMW do?

The transmission wiring harness will be inspected and rerouted or, in some cases, replaced and rerouted, for free which could take approximately one hour.

 

What if I am not the current owner of this vehicle?

You can update the vehicle ownership or your contact information by completing the enclosed postage-paid card or by registering at https://www.bmwusa.com/myBMW. If you are a vehicle lessor, Federal Regulations require you to forward this notice to your lessee within ten days.

 

What if I have questions or experience problems?

For the latest updates to this recall, please visit www.bmwusa.com/recall. Should you have any questions about  this recall, please contact your authorized BMW center. If you need additional assistance, contact BMW Customer Relations and Services at 1-800-525-7417 or at CustomerRelations@bmwusa.com.

If your BMW center is unable to remedy the defect without charge or within a reasonable period of time, you may notify the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, DC 20590, call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153), or go to https://www.safercar.gov.

 

Please be assured that your safety is important to us, and we sincerely apologize if this recall causes any inconvenience. We recommend that you and your passengers wear your safety belt at all times.

 

Sincerely,

 

BMW of North America, LLC

 

Spanish translation on back side
Traducción en español en el lado inverso

 

 


IMPORTANTE RETIRADA POR MOTIVOS DE SEGURIDAD

Repuesto disponible

Este aviso se aplica a su vehiculo,
Campana de retirada n.0 19V-883: Arnes del cableado de la transmisi6n

Febrero de 2020

 

Estimado propietario o arrendatario de un vehfculo BMW:

Le enviamos este aviso en virtud de la National Traffic and Motor Vehicle Safety Act (Ley Nacional de Seguridad de Transito y Vehfculos). BMW AG ha determinado que algunos vehfculos de los modelos M5 y M8 de BMW, correspondientes a los anos 2019-2020, tienen un defecto relacionado con la seguridad de vehfculos motorizados. Segun nuestros registros, usted es propietario de un vehfculo potencialmente afectado.

 

¿Por que nos ponemos en contacto con usted?

Nos complace informarle que estamos listos para realizar esta retirada. Si no se ha hecho la retirada, comuniquese de inmediato con el centro autorizado de BMW para programar una cita. Visite www.bmwusa.com/dealer para localizar el centro de BMW mas cercano.

 

¿Que podria suceder?

Debido a su ubicaci6n/enrutamiento, el arnes de cableado de la transmisi6n podrfa danarse. Si esto ocurre mientras conduce, el vehfculo puede perder la propulsi6n y la transmisi6n podrfa cambiar a neutral de forma inesperada, aumentando el riesgo de sufrir un accidente.

Si nota que mientras conduce la transmisi6n cambia inesperadamente a neutral o si, cuando presiona el pedal del acelerador, escucha un aumento en el ruido del motor pero la velocidad del vehiculo no aumenta, es posible que su vehiculo tenga este problema. Tambien es posible que vea una “N” (en lugar de una “D”) en el tablero de  instrumentos. Si esto ocurre, alejese con cuidado del transito y detengase en un lugar seguro lo antes posible. Todos los ocupantes deben salir del vehiculo con cuidado y trasladarse a un lugar seguro lejos del transito. No siga conduciendo el vehiculo. Comuniquese de inmediato con BMW Roadside Assistance (Asistencia en la carretera de BMW) llamando al 1-800-332-4269 para que lleven su vehiculo al centro autorizado de BMW mas cercano.

Si usted no es la (nica persona que conduce este vehiculo, comparta esta informaci6n importante con todos los  demas conductores y pasajeros.

 

¿Que hara BMW?

Se inspeccionara el arnes del cableado de la transmisi6n y se lo volvera a enrutar y, en algunos casos, se cambiara y volvera a enrutar sin cargo; esto podrfa demorar aproximadamente una hora.

 

¿Que ocurre si no soy el propietario actual de este vehiculo?

Puede completar la tarjeta con respuesta postal paga adjunta o registrarse en https://www.bmwusa.com/myBMW para actualizar la informaci6n de la titularidad del vehfculo o su informaci6n de contacto. Si usted es arrendador del vehiculo, las reglamentaciones federales exigen que reenvie este aviso a su arrendatario en un plazo de diez dias.

 

¿Que debo hacer si tengo alguna pregunta o algun problema?

Para ver las ultimas actualizaciones de esta retirada, visite www.bmwusa.com/recall. Si tiene alguna pregunta sobre esta retirada, comunfquese con el centro autorizado de BMW. Si necesita asistencia adicional, comunfquese con el BMW Customer Relations and Services (Servicio de Atenci6n al Cliente de BMW) llamando al 1-800-525-7417 o por correo electr6nico a CustomerRelations@bmwusa.com.

Si el centro de BMW no puede resolver el defecto sin cargo o en un plazo razonable, puede notificar al administrador de la National Highway Traffic Safety Administration (Administraci6n Nacional de Seguridad de Transito en Carreteras), 1200 New Jersey Ave., S.E., Washington, DC 20590, llamar a la Vehicle Safety Hotline (Lfnea gratuita directa de seguridad vehicular) al 1-888-327-4236 (TTY: 1-800-424-9153) o visitar https://www.safercar.gov.

Le aseguramos que nos importa su seguridad y le pedimos sinceras disculpas si esta retirada le causa algun inconveniente. Recomendamos que usted y sus pasajeros utilicen el cintur6n de seguridad en todo momento.

 

Atentamente.

 

BMW of North America, LLC

 

English version on front side
Versión en inglés en el frente

 


4 Affected Products

Vehicles

MAKE MODEL YEAR
BMW M5 2019-2020
BMW M8 2020
BMW M8 GRAN COUPE 2020

 


11 Associated Documents

Remedy Instructions and TSB re Transmission Wiring Harness

RCRIT-19V883-6579.pdf 2141.801KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.04 MB]

 


Recall Quarterly Report #1, 2020-1

RCLQRT-19V883-1762.PDF 211.142KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.19 KB]

 


Owner Notification Letter(Part 577)

RCONL-19V883-9077.pdf 1257.554KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.20 MB]

 


Recall Acknowledgement

RCAK-19V883-9052.pdf 286.656KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [279.94 KB]

 


Defect Notice 573 Report

RCLRPT-19V883-9390.PDF 215.87KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [210.81 KB]

 


Remedy Instructions and TSB

RCRIT-19V883-9113.pdf 2126.194KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.03 MB]

 


Remedy Instructions and TSB

RCRIT-19V883-4244.pdf 2150.058KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.05 MB]

 


Manufacturer Notices(to Dealers,etc)- BMW Recall 19V-XXX: Transmission Wiring Harness

RCMN-19V883-0990.pdf 198.771KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [194.11 KB]

 


Remedy Instructions and TSB

RCRIT-19V883-8439.pdf 2164.447KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.06 MB]

 


Recall Quarterly Report #2, 2020-2

RCLQRT-19V883-2317.PDF 211.239KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.29 KB]

 


Recall Quarterly Report #3, 2020-3

RCLQRT-19V883-3831.PDF 211.326KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.37 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V883&docType=RCL

 


 

SaleBestseller No. 1
XFasten Wire Harness Tape, 3/4-Inch by 50-Foot (5-Pack), High Temp Wiring Loom Harness Self-Adhesive Felt Cloth Electrical Tape for Automotive Engine and Electrical Wiring
  • High temp Wire Harness Automotive Cloth Tape with excellent sound and rattle dampening performance. Lessens coil whining and lasts well against elevated temperatures (-40℉ - 257℉).
  • Sports a race-spec heavy-duty bundling performance but cleanly tears with just bare hands, EMPOWERING average car owners with LITTLE TO NO EXPERIENCE in automotive maintenance to achieve PROFESSIONAL-GRADE results in function and form.
  • This Wire Loom Tape features an extremely strong adhesive but does not turn into a messy goo. Rated to last up to 6 years and can easily get you through 150k miles of mileage.
  • Its bi-directional weave makes it puncture-resistant and abrasion and corrosion-resistant. This automotive felt tape preserves cables in their pristine condition.
  • This engine tape wrap is similar, if not better, in thickness, tensile strength and looks with OEM wire harness tapes. Extra-sticky adhesive enables users to bundle hard-to-reach cables quickly.
Bestseller No. 2
Tesa's Most Advanced High Heat Harness Tape 51036 Mercedes, BMW, Audi, VW
  • -The most advanced high heat harness tape available
  • -Superior abrasion & heat resistant
  • -Resist chemical and fluid from engine compartment
  • -Solvent-free advanced acrylic adhesive & flame-retardant
  • -1 roll of Tesa 51036 (each roll is 19mm wide X 25meters long)
Bestseller No. 3
5 Rolls Tesa's Most Advanced High Heat Harness Tape 51036 Mercedes, BMW, Audi, VW
  • -The most advanced high heat harness tape available
  • -Superior abrasion & heat resistant
  • -Resist chemical and fluid from engine compartment
  • -Solvent-free advanced acrylic adhesive & flame-retardant
  • -5 rolls of Tesa 51036 (each roll is 19mm wide X 25meters long)
Bestseller No. 4
RED WOLF Wiring Harness Tape High Temp Wire Cable Loom Self-Adhesive Fabric Tape for Electrical Automotive Engine Harness Wrap Protection Noise Damping Cables Fixed 3/4 Inch x 50 FT 5 Rolls
  • Widely application: The material of wire harness cloth tape is soft and corrosion-resistant, which is suitable for the use of wire harness in automobile interior noise reduction part, such as wire harness of the dashboard, main harness wound and applied for wire joint and wire fixing. It can also sort out home appliance wiring and more.
  • Easy to tear. Just stick one end of tape to cable, start pulling and wrapping onto the cable and tear it gently. No need scissors and other tools. You can decide the length of the wire cloth tape according to you needs.
  • Professional cloth tape material: It is made of polyester non-woven fabric and strong acrylic pressure sensitive adhesive. High viscosity, high temperature resistance ( -40°F ~ 221°F ), well seal and excellent flexibility.
  • Excellent performance: The wiring harness tape maintains features high adhesive force, good noise reduction, hand tearable and heat insulation performance, and wear resistance. It is suitable for electrical automotive engine and circuit maintenance to achieve the purpose of insulation protection.
  • Specification: A set of 5 rolls wire harness cloth tap. SIZE: Each roll black electrical harness tape is 50 FT long and 3/4 inch wide. It is work for your different daily needs in diversified use scenarios.
Bestseller No. 5
Wire Harness Cloth Electrical Tape Loom Wiring Automotive Heat Proof Adhesive Fabric for Wrap Protection Insulation Cable Fixed (2 Roll,50 mm)
  • Enough to Use: you will get 2 rolls of wire harness tapes in the package, measuring approx. 2 inches x 49.2 ft/ 50 mm x 15 m for each; The proper size and sufficient length is suitable for your different daily needs in many use scenarios
  • Safe Material: the wire harness tape is made of polyester non woven fabric material, quality pressure sensitive adhesive, high temperature and wear resistance, which can be applied for a long time
  • Nice Performance: the adhesive fabric tape has nice noise reduction and heat insulation performance, very suitable for automotive engine and circuit maintenance to achieve the purpose of insulation protection
  • Easy to Use: the wire loom tape is simple and convenient to use, just wrap the tape on the wire and tear it gently, and you can decide the length of the tape according to your own needs
  • Scope of Usage: the cloth electrical tape is suitable for automobile interior noise reduction part, such as instrument panel harness and main harness wound, and can also be applied for wire joint and wire fixing
Bestseller No. 6
Oyviny Electrical Wire Harness Cloth Tape 1 Inch x 50 Feet Self-Adhesive Wire Loom Cloth Tape for Automobile Electrical and Engine Wire Noise Dampening, Wiring Harness Tape for Audio Wire Harness
  • Wire Harness Cloth Tape Application: Automotive wire loom tape is widely used in the area near the engine, battery or on normal wire harness and also suitable for the use of wire harness in automobile interior noise reduction part, such as instrument panel harness. Wrap any wires that need to be repaired
  • Temperature Resistance: Electrical wiring harness cloth tape made of high-quality polyester non-woven fabric and strong acrylic pressure sensitive adhesive, with high adhesive Force, abrasion resistance and high-temperature resistance (-40℉- 225℉)
  • Easy to Tear: Oyviny automotive cloth tape is easy to tear and convenient to use, just wrap the harness cloth tape around the wiring harness and gently tear it apart, No tools required! You could tear the tape at any length according to your need
  • Good Performance: Automotive wire loom harness cloth tape is wear-resistant and with strong anti-aging, which can be applied for a long time. It is also suitable for automotive circuit and engine maintenance to achieve the effect of insulation protection
  • Harness Cloth Tape Size: Package comes with 5 rolls 25mm x 15m electrical wire harness tape. Each roll radio wiring harness cloth tape is 1 inch width and 50 feet length. The size and length is suitable for your daily use
Bestseller No. 7
10 Rolls Tesa's Most Advanced High Heat Harness Tape 51036 Mercedes, BMW, Audi, VW
  • The most advanced high heat harness tape available
  • Rated to 150C, Superior abrasion resistance
  • Resists chemicals and fluids
  • AAA adhesive, self extinguishing
Bestseller No. 8
XFasten Wire Harness Tape 10-Pack 3/4 Inch x 50-Feet 500ft Total Residue-Free High Heat Resistant Automotive Wire Loom Tape Cloth Electrical Tape Automotive Fabric High Heat Cable Wrap Tape
  • OEM-GRADE AUTOMOTIVE WIRE LOOM TAPE that’s specifically designed for high temp wirings. Our wiring harness tape prevents oil build-up, abrasion, and contains 10 rolls at 50 Feet, for a total of 500 feet.
  • HEAVY-DUTY. With a tensile strength of 160lb/in, this cloth tape automotive withstands daily wear and tear, extreme heat, and humidity for up to 12 years without weakening or unraveling.
  • RESIDUE-FREE. With a silicone adhesive, our fabric electrical tape will not leave a messy goo upon removal. This heat resistant wire loom tape prevents coil rattling, making it an essential high temp automotive tape for those who want silent and PRO-GRADE cable wrap results.
  • EXCELLENT THERMALS. Operating at -40°F to 257°F, this high temp electrical tape can also be used under the hood, PC, or on high heat electrical wire harness wrap.
  • INSTALLS CLEANLY. Made from fabric-polycarbonate composite, this automotive electrical tape can torn with bare hands, while being stretchy for accessing hard-to-reach areas.
SaleBestseller No. 9
Pushglossy 30 Pcs Wire Harness Tape 3/4 Inch by 50 Foot High Temp Wiring Loom Harness Electrical Tape Black Adhesive Fabric Tape for Automotive Engine and Electrical Wiring
  • Generous Tape Dimensions for Wide Applications: this automotive cloth tape measures approx. 3/4 inch x 50 ft/ 19 mm x 15 m, making it an ideal size for many uses; The cloth electrical tape can cater to your diverse needs, providing high resistance against dirt and aging, whether insulation or protection tasks, or noise reduction in your automobile's interior, doors, and stereo wrapping
  • Quality Material for Long Lasting Durability: the wire harness tape is made from polyester fabric, quality pressure sensitive adhesive, no solvent residue; This material is not only reliable but also an ideal choice for different everyday scenarios in your car; Its robust adhesion ability means it won't turn into a chaotic sticky mass, ensuring a clean and efficient application process
  • Designed for Convenience: the wire harness automotive cloth tape is designed with user convenience in mind; Simply wind the tape around your wiring, then tear off the needed length; No need for scissors or other tools; You'll find this handy attribute useful during those intricate automotive projects
  • Ideal Performance Under Pressure: boasting high resistance to high temperatures and wear, this wire harness tape ensures ideal noise reduction and thermal insulation performance; It also aims to deliver insulation protection for automotive engine electrical circuits; Harnessing powerful adhesive strength yet remaining non messy, this harness cloth tape has a rated lifespan of 6 years and can help you navigate seamlessly through 150, 000 miles
  • Versatile Utilities for Broad Serviceability: the soft wire harness tape is versatile and can be applied in various parts of an automobile; With ideal corrosion resistance, it's suitable for noise reduction parts such as dashboard harness wrap, main harness windings, and wire connections and fixation
Bestseller No. 10
Tesa Wire Loom Harness Tape Used By Mercedes BMW VW Audi
  • Big 19mm X 25m roll
  • Matches other wire looms in your car
  • Genuine German Quality
  • Good adhesion
  • Gives professional appearance

Last update on 2024-03-12 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...